86-0769-22327568
4/F, Block B, Ruilian Zhenxing Industrial Park, Xinhe Ind. Area, Jianshazhou, Wanjiang District, Dongguan, Guangdong, China (Mainland)
| Model | Power (V) | Input voltage (W) | Display | RS-485 | Matched standard motor | Matched gear motor |
| SA-D60LRD | 24 | 60 | ♦ | ♦ | M60L32A/M60L34A | M60L32/M60L34 |
| SA-D120LRD | 24 | 120 | ♦ | ♦ | M120L34C/M120L35B | M120L34https://M120L35 |
| SA-D200NRD | 48 | 200 | ♦ | ♦ | M200N35C | M200N35 |
| SA | D | 60 | L | R | D |
| Series name | Type | Power | Supply voltage | Motor leads number | Display |
| Controller | 60:60W | L:DC24V | R:485Communication | D:Display | |
| 120:120W | N:DC48V | None: No communication | None: No display | ||
| 200:200W | M:AC110V | ||||
| H:AC220V |
| ♦ Equipped with a display device ♦ 5 speed regulation modes ♦ RS-485 communication port | ♦ Self fault clearance and self-protection function ♦ High speed(100-4000r/min), high efficiency(30~200W) |
| One click to start/stop the motor | Rotating direction selection |
 | |
| Move the running switch rightwards to RUN, then the motor starts rotating. Move the switch leftwards to STAND-BY, the motor stops. | Press the Page Up/Page Down button for 3s, the motor will rotate clockwise/anticlockwise. Direction conversion is available when motor is running. |
| Connector connection | Screw free wiring |
 | |
| The connection of SA driver and motor can be reached by connector. | Just click the orange button and insert wires to finish wiring arrangement. No need weld or professional tools. |
| Panel speed regulation | Digital setting to set the speed |
 | |
| Rotate the knob clockwise to accelerate, while anticlockwise to decelerate, press the knob to /confirm/i. | Enter the digital setting mode to set the revolving speed, press the SET button to /confirm/i. |
| PWM to set the speed | Pulse Frequency to set the speed |
 | |
| When speed setting mode is set as PWM, the motor speed will vary via duty ratio(1%-99%). Refer to the following diagram. | When pulse frequency mode is /confirm/ied, speed will vary via pulse frequency(100HZ~3KHZ). Refer to the following diagram. |
| Analog setting of acceleration and deceleration time | |
 | |
| On the back of the SD driver, there are acceleration time knob(ACC) and deceleration time knob(DEC). 0.2s(default value) to 15 sec are available. | Acceleration and deceleration time can be set by data mode. |
| Set the speed upper/lower limit | Brake stop |
 | |
| Speed upper/lower limit can be set, the default value is 0-4000r/min. | When FWD and REV is set as ON, the motor stop rapidly, but the needed time depends on the load inertia. The least time is 200ms. |
| Multistage speed data selection | Direction control by upper computer |
 | |
| Four periods(SPD1,SPD2,SPD3, SPD4) of speed can be set. Speed can be switched by MO and M1 terminal control. | When control mode is set as I/O port, motor direction can be set by upper computer. When REV or FWD is set as ON, motor direction shifts. |
| Speed signal output | Alarm output |
 | |
| 30 pulses output for 1r rotation. Speed output signal can be detected by upper computer. | When motor is overload or locked, alarm signal will detected by upper computer. |
| Parameter display | Error display |
 | |
| Parameters such as Speed, Current, Voltage and Temperature can be displayed. | When malfunction occurs, fault code can be displayed on display panel or I/O port. |
We are direct manufacture of BLDC Motor/driver, for more and catalog, please contact us!
